diff --git a/documents/README/changelog/Changelog.md b/documents/README/changelog/Changelog.md index 61b2da6..aa46338 100644 --- a/documents/README/changelog/Changelog.md +++ b/documents/README/changelog/Changelog.md @@ -9,6 +9,8 @@ * YamBMS 1.8.2 : * Set esphome `min_version` to `2026.11.0` * Updated EG4 LL-V2 component to [v1.1.1](https://github.com/RAR/esphome-eg4-bms/releases/tag/v1.1.1) : it builds on ESPHome 2026.11, which removed `format_hex_pretty()` ; v1.1.0 fails to compile with `'format_hex_pretty' was not declared in this scope` + * Updated EG4 LL-V2 component to [v1.1.4](https://github.com/RAR/esphome-eg4-bms/releases/tag/v1.1.4) : a pack goes offline when either of its two register blocks stops giving valid replies, and that block's sensors go unknown ; before, one good block kept the pack online with the other block's values going stale. The bus now waits `turnaround_time` (50 ms) after a reply before the next request, as a request sent right after another pack's reply was often not answered, and only the reply to the request in flight ends that wait ([RAR/esphome-eg4-bms#9](https://github.com/RAR/esphome-eg4-bms/issues/9)) + * EG4 LL-V2 errors bitmask : protection bit 12 "Low Capacity" no longer raises a General alarm ; EG4 packs hold it while full and charging has stopped, so every full charge reported an alarm to the inverter (#342). Discharge over temperature and discharge under temperature protection, which were not mapped, now raise the high and low temperature alarms * ESPHome 2026.11 requires a `relation` on every sub-device : the BMS, Shunt, Balancer, sniffer, Deye, board, YamBMS and inverter link devices are all declared as `via`, which is how Home Assistant already showed them, so your devices and entities stay as they are * Waveshare ESP32-S3 Touch-LCD 4.3, 4.3B and 7 : removed the `enable_pin` workaround added in 1.8.1 for `Pin 2 is used in multiple places`, ESPHome 2026.11 now resolves this conflict itself ; the display and the backlight behave as before * JK RS485 (JK-PB, and recent JK-B using the `JK BMS RS485 Modbus V1.0` protocol) : the sniffer packages temporarily load the [JK RS485 components](https://github.com/Sleeper85/esphome-components/tree/dev) 1.2 from the `dev` branch, until 1.2 is released on `main`. Full list in the [JK RS485 changelog](https://github.com/Sleeper85/esphome-components/blob/dev/documents/README/changelog/Changelog.md). Main fixes : diff --git a/packages/bms/bms_combine_EG4_RS485_modbus.yaml b/packages/bms/bms_combine_EG4_RS485_modbus.yaml index 4d81230..c72a078 100644 --- a/packages/bms/bms_combine_EG4_RS485_modbus.yaml +++ b/packages/bms/bms_combine_EG4_RS485_modbus.yaml @@ -1,5 +1,5 @@ -# Updated : 2026.11.09 -# Version : 2.0.4 +# Updated : 2026.11.15 +# Version : 2.0.5 # GitHub : https://github.com/RAR/esphome-eg4-bms # YamBMS ( Yet another multi-BMS Merging Solution ) @@ -22,7 +22,7 @@ substitutions: eg4_modbus_id: modbus_eg4 external_components: - - source: github://RAR/esphome-eg4-bms@v1.1.1 + - source: github://RAR/esphome-eg4-bms@v1.1.4 refresh: 0s packages: diff --git a/packages/bms/bms_errors_bitmask_EG4_LLV2_RS485_Modbus.yaml b/packages/bms/bms_errors_bitmask_EG4_LLV2_RS485_Modbus.yaml index da53d85..dc5b905 100644 --- a/packages/bms/bms_errors_bitmask_EG4_LLV2_RS485_Modbus.yaml +++ b/packages/bms/bms_errors_bitmask_EG4_LLV2_RS485_Modbus.yaml @@ -1,5 +1,5 @@ -# Updated : 2025.12.22 -# Version : 2.0.1 +# Updated : 2026.11.10 +# Version : 2.0.2 # GitHub : https://github.com/RAR/esphome-eg4-bms # YamBMS ( Yet another multi-BMS Merging Solution ) @@ -43,6 +43,7 @@ # Bit 10 Charge Under Temp 0000 0100 0000 0000 0x0400 # Bit 11 Discharge Under Temp 0000 1000 0000 0000 0x0800 # Bit 12 Low Capacity 0001 0000 0000 0000 0x1000 + # (held while a full pack has stopped charging, so it is not mapped to an alarm) # Bit 13 Discharge SC 0010 0000 0000 0000 0x2000 # +--------------------------------------+ @@ -79,8 +80,11 @@ sensor: - throttle: 10s - delta: 1 lambda: |- - uint32_t bms_errors_bitmask = id(bms${bms_id}_errors_bitmask).state; - uint32_t bms_protection_bitmask = id(bms${bms_id}_protection_bitmask).state; + // The component publishes NaN for a register block that has gone stale (no bits) + float bms_errors = id(bms${bms_id}_errors_bitmask).state; + float bms_protection = id(bms${bms_id}_protection_bitmask).state; + uint32_t bms_errors_bitmask = std::isnan(bms_errors) ? 0 : (uint32_t) bms_errors; + uint32_t bms_protection_bitmask = std::isnan(bms_protection) ? 0 : (uint32_t) bms_protection; uint16_t yambms_errors_bitmask = 0; if (bms_errors_bitmask > 0) @@ -100,11 +104,12 @@ sensor: if (bms_protection_bitmask & 0x0010) yambms_errors_bitmask |= 0x0100; if (bms_protection_bitmask & 0x0020) yambms_errors_bitmask |= 0x0080; if (bms_protection_bitmask & 0x0100) yambms_errors_bitmask |= 0x0020; + if (bms_protection_bitmask & 0x0200) yambms_errors_bitmask |= 0x0008; if (bms_protection_bitmask & 0x0400) yambms_errors_bitmask |= 0x0040; + if (bms_protection_bitmask & 0x0800) yambms_errors_bitmask |= 0x0010; if (bms_protection_bitmask & 0x2000) yambms_errors_bitmask |= 0x0400; if (bms_protection_bitmask & 0x0040) yambms_errors_bitmask |= 0x0001; if (bms_protection_bitmask & 0x0080) yambms_errors_bitmask |= 0x0001; - if (bms_protection_bitmask & 0x1000) yambms_errors_bitmask |= 0x0001; } return yambms_errors_bitmask; diff --git a/packages/bms/bms_sensors_EG4_LLV2_RS485_bms_full.yaml b/packages/bms/bms_sensors_EG4_LLV2_RS485_bms_full.yaml index 7b8a0c8..aefdd46 100644 --- a/packages/bms/bms_sensors_EG4_LLV2_RS485_bms_full.yaml +++ b/packages/bms/bms_sensors_EG4_LLV2_RS485_bms_full.yaml @@ -1,5 +1,5 @@ -# Updated : 2026.11.09 -# Version : 2.0.6 +# Updated : 2026.11.15 +# Version : 2.0.7 # GitHub : https://github.com/RAR/esphome-eg4-bms # YamBMS ( Yet another multi-BMS Merging Solution ) @@ -34,7 +34,7 @@ substitutions: # +--------------------------------------+ external_components: - - source: github://RAR/esphome-eg4-bms@v1.1.1 + - source: github://RAR/esphome-eg4-bms@v1.1.4 refresh: 0s eg4_bms: