diff --git a/documents/README/Board_LilyGo_T-Connect.md b/documents/README/Board_LilyGo_T-Connect.md index 59d89f1..8bfc2d1 100644 --- a/documents/README/Board_LilyGo_T-Connect.md +++ b/documents/README/Board_LilyGo_T-Connect.md @@ -27,7 +27,7 @@ The LilyGo T-Connect is a multi-functional development board based on the ESP32- The T-Connect is available as a single version with the following specifications: | Specification | Details | -| --- | --- | +|---------------|---------| | Model | T-Connect | | MCU | ESP32-S3-R8 | | FLASH | 16MB | @@ -45,15 +45,18 @@ The T-Connect is available as a single version with the following specifications **Note:** The T-Connect supports switching configuration between CAN and RS485 modules through onboard jumpers, allowing maximum flexibility with up to 3 RS485 ports + 1 CAN port simultaneously. -## BMS Support Capacity +## Interfaces Support Capacity Based on hardware limitations and testing, this board supports: -| Communication Method | Maximum BMS | Notes | -|----------------------|-------------|-------| -| **RS485** | Multiple BMS | Best option for monitoring many BMS units | -| **UART** | 3× BMS | Must be connected to the GPIOs header | -| **Bluetooth (BLE)** | 3× BMS | BLE stack consumes significant RAM, may cause crashes/reboots | +| Interface | Maximum | Notes | +|-----------|---------|-------| +| **CAN** | 1x bus | CAN bus to BMS or Inverter | +| **RS485** | 3x bus | Best option for monitoring many BMS of the same brand (**shared with UART**) | +| **UART** | 3× devices¹ | Must be connected to the **GPIOs header** (**shared with RS485**) | +| **Bluetooth (BLE)** | 3× devices¹ | BLE stack consumes significant RAM, may cause crashes/reboots | + +¹ BMS / Balancer / Shunt **Note:** These are theoretical limits. Not all combinations have been tested. @@ -89,7 +92,7 @@ The T-Connect board features 4 communication ports that share pins through a swi **Pin Assignment :** | Port | TX Pin | RX Pin | Protocol | -| --- | --- | --- | --- | +|------|--------|--------|----------| | Port 1 | IO4 | IO5 | RS485 | | Port 2 | IO6 | IO7 | RS485 | | Port 3 | IO17 | IO18 | RS485 | @@ -122,7 +125,7 @@ The CAN bus port is positioned at location **No.4** (see photo at the beginning To connect an RS485 device to any of the configured RS485 ports: | RS485 | Terminal Block | -| --- | --- | +|-------|----------------| | - | SG : Shield/Signal Ground (optional but recommended) | | A + | L (RS485 A, Data+ non-inverting) | | B - | H (RS485 B, Data- inverting) | @@ -159,7 +162,7 @@ To connect an RS485 device to any of the configured RS485 ports: To connect a CAN bus device to the CAN port: | CAN bus | Terminal Block | -| --- | --- | +|---------|----------------| | - | SG : Shield/Signal Ground (optional but recommended) | | CAN L | L (CAN Low) | | CAN H | H (CAN High) | @@ -332,7 +335,7 @@ For a typical YamBMS setup with the LilyGo T-Connect board: ### Waveshare ESP32-S3-RS485-CAN vs LilyGo T-Connect | Feature | Waveshare | LilyGo T-Connect | -| ------- | --------- | ---------------- | +|---------|-----------|------------------| | RS485 Ports | 1 (isolated) | Up to 3 (isolated) | | CAN Ports | 1 (isolated) | 1 (isolated) | | Built-in Termination | ✅ Yes (120Ω jumper-selectable) | ❌ No (external resistors required) | diff --git a/documents/README/Board_M5Stack_AtomS3.md b/documents/README/Board_M5Stack_AtomS3.md index 4e9c47d..9a6a106 100644 --- a/documents/README/Board_M5Stack_AtomS3.md +++ b/documents/README/Board_M5Stack_AtomS3.md @@ -33,7 +33,7 @@ The M5Stack **AtomS3** combined with the **Atomic CAN Base** provides a compact Choose one AtomS3 controller to clip onto the Atomic CAN Base: | [AtomS3 Lite](https://docs.m5stack.com/en/core/AtomS3%20Lite) | [AtomS3](https://docs.m5stack.com/en/core/AtomS3) | [AtomS3R (8MB PSRAM)](https://docs.m5stack.com/en/core/AtomS3R) | -| --- | --- | --- | +|-----|-----|-----| | | | | | Model | Flash | PSRAM | Display | IMU | Best For | @@ -47,7 +47,7 @@ Choose one AtomS3 controller to clip onto the Atomic CAN Base: ### Base & Communication Units | [Atomic CAN Base](https://docs.m5stack.com/en/atom/Atomic%20CAN%20Base) | [CAN Unit](https://docs.m5stack.com/en/unit/can) | [RS485 Unit](https://docs.m5stack.com/en/unit/iso485) | -| --- | --- | --- | +|-----|-----|-----| | | | | | Component | Type | Features | Use Case | @@ -56,15 +56,18 @@ Choose one AtomS3 controller to clip onto the Atomic CAN Base: | **[CAN Unit](https://docs.m5stack.com/en/unit/can)** (U085) | HY2.0 Unit | Isolated CAN via Grove port | Alternative CAN solution | | **[RS485-ISO Unit](https://docs.m5stack.com/en/unit/iso485)** (U094) | HY2.0 Unit | Isolated RS485, up to 500kbps, 256 nodes | For RS485 BMS or multi-node | -## BMS Support Capacity +## Interfaces Support Capacity Based on hardware limitations and testing, this board supports: -| Communication Method | Maximum BMS | Notes | -|----------------------|-------------|-------| -| **RS485** | Multiple BMS | Best option for monitoring many BMS units | -| **UART** | 3× BMS | The 2nd and 3rd UARTs must be connected on Atomic CAN Base GPIOs | -| **Bluetooth (BLE)** | 3× BMS | BLE stack consumes significant RAM, may cause crashes/reboots | +| Interface | Maximum | Notes | +|-----------|---------|-------| +| **CAN** | 1x bus | CAN bus to BMS or Inverter (**after adding a CAN base/unit**) | +| **RS485** | 1x bus | Best option for monitoring many BMS of the same brand (**after adding a RS485 base/unit**) | +| **UART** | 3× devices¹ | CAN be connected to the **HY2.0 interface** or **Atomic Base GPIOs header** (**shared with RS485**) | +| **Bluetooth (BLE)** | 3× devices¹ | BLE stack consumes significant RAM, may cause crashes/reboots | + +¹ BMS / Balancer / Shunt **Note:** These are theoretical limits. Not all combinations have been tested. For large installations with many BMS units, consider boards with more GPIOs like the LilyGo T-Connect or Waveshare ESP32-S3-RS485-CAN. @@ -73,12 +76,13 @@ Based on hardware limitations and testing, this board supports: ### Hardware Specifications | Specification | Details | -|--------------|---------| +|---------------|---------| | **Microcontroller** | ESP32-S3FN8 | | **Processor** | Xtensa 32-bit LX7 dual-core @ up to 240MHz | | **Flash** | 8MB | | **PSRAM** | None (AtomS3 Lite/AtomS3) / 8MB Octal SPI (AtomS3R) | | **Display** | 0.85" IPS LCD, 128×128 resolution | +| **UART** | 1x HY2.0 interface (not isolated) | | **IMU** | MPU6886 (6-axis gyro + accel, I2C 0x68) | | **Button** | 1× Programmable button | | **Infrared** | IR transmitter built-in | @@ -106,7 +110,7 @@ Based on hardware limitations and testing, this board supports: **Internal Connections:** | Peripheral | GPIO Pins | Notes | -|-----------|-----------|-------| +|------------|-----------|-------| | **LCD Display** | MOSI: G21, SCK: G17, CS: G15, RS: G33, RST: G34, BL: G16 | SPI interface | | **MPU6886 (IMU)** | SDA: G38, SCL: G39 | I2C address 0x68 | | **IR Transmitter** | Built-in | For infrared control | @@ -116,7 +120,7 @@ Based on hardware limitations and testing, this board supports: ### Hardware Specifications | Specification | Details | -|--------------|---------| +|---------------|---------| | **CAN Transceiver** | CA-IS3050G (isolated) | | **Maximum Rate** | 1 Mbps | | **Supported Nodes** | Up to 110 nodes | @@ -153,7 +157,7 @@ The Atomic CAN Base connects to AtomS3 through the bottom pins: If you need RS485 communication (e.g., for RS485 BMS, multi-node), add the **RS485-ISO Unit (U094)**: | Specification | Details | -|--------------|---------| +|---------------|---------| | **Isolation Chip** | CA-IS3082W | | **Maximum Rate** | 500 kbps | | **Supported Nodes** | Up to 256 nodes | @@ -264,7 +268,7 @@ If you have trouble uploading firmware to the AtomS3: ### Screen Specifications | Specification | Details | -|--------------|---------| +|---------------|---------| | **Size** | 0.85 inch IPS LCD | | **Resolution** | 128 × 128 pixels | | **Color Depth** | 65K colors | diff --git a/documents/README/Board_Waveshare_ESP32-S3-RS485-CAN.md b/documents/README/Board_Waveshare_ESP32-S3-RS485-CAN.md index 9580be3..1665014 100644 --- a/documents/README/Board_Waveshare_ESP32-S3-RS485-CAN.md +++ b/documents/README/Board_Waveshare_ESP32-S3-RS485-CAN.md @@ -27,7 +27,7 @@ The Waveshare ESP32-S3-RS485-CAN is an industrial-grade WiFi wireless communicat ## Board Specifications | Specification | Details | -| --- | --- | +|-----|-----| | Microcontroller | ESP32-S3-WROOM-1 | | Processor | Xtensa 32-bit LX7 dual-core @ up to 240MHz | | FLASH | 16MB | @@ -35,6 +35,7 @@ The Waveshare ESP32-S3-RS485-CAN is an industrial-grade WiFi wireless communicat | Wireless | Wi-Fi 802.11 b/g/n (2.4GHz) / Bluetooth 5.0 (LE) | | RS485 | 1× Isolated RS485 interface | | CAN Bus | 1× Isolated CAN interface | +| UART | 1x SH1.0 interface (not isolated) | | Power Input (DC Terminal) | 7-36V DC (wide range) | | Power Input (USB) | 5V via USB Type-C | | Isolation | Power isolation + Optocoupler isolation | @@ -43,15 +44,18 @@ The Waveshare ESP32-S3-RS485-CAN is an industrial-grade WiFi wireless communicat | Enclosure | Rail-mounted ABS protective case | | Programming | USB Type-C (firmware download & debugging) | -## BMS Support Capacity +## Interfaces Support Capacity Based on hardware limitations and testing, this board supports: -| Communication Method | Maximum BMS | Notes | -|----------------------|-------------|-------| -| **RS485** | Multiple BMS | Best option for monitoring many BMS units | -| **UART** | 3× BMS | Must be connected to the GPIOs header | -| **Bluetooth (BLE)** | 3× BMS | BLE stack consumes significant RAM, may cause crashes/reboots | +| Interface | Maximum | Notes | +|-----------|---------|-------| +| **CAN** | 1x bus | CAN bus to BMS or Inverter | +| **RS485** | 1x bus | Best option for monitoring many BMS of the same brand | +| **UART** | 3× devices¹ | Can be connected to the **SH1.0 interface** or **GPIOs header** (**shared with RS485**) | +| **Bluetooth (BLE)** | 3× devices¹ | BLE stack consumes significant RAM, may cause crashes/reboots | + +¹ BMS / Balancer / Shunt **Note:** These are theoretical limits. Not all combinations have been tested. @@ -131,7 +135,7 @@ The CAN port typically has a **2-pin screw terminal block**: To connect an RS485 device to the RS485 port: | RS485 | Terminal Block | -| --- | --- | +|-------|----------------| | A + | RS485 A+ (Data+ non-inverting) | | B - | RS485 B- (Data- inverting) | @@ -154,7 +158,7 @@ To connect an RS485 device to the RS485 port: To connect a CAN device to the CAN port: | CAN bus | Terminal Block | -| --- | --- | +|---------|----------------| | CAN H | CAN H (CAN High) | | CAN L | CAN L (CAN Low) | @@ -219,7 +223,7 @@ The board includes an **onboard 120Ω CAN termination resistor**. The board includes several LED indicators for monitoring system status: | LED | Color | Function | -| --- | --- | --- | +|-----|-------|----------| | **PWR** | Red/Green | Power indicator - lights up when board is powered | | **RS485 TX** | Green | Lights up when RS485 port **sends** data | | **RS485 RX** | Blue | Lights up when RS485 port **receives** data | @@ -350,7 +354,7 @@ Waveshare provides demo firmware with a web interface: ### Waveshare ESP32-S3-RS485-CAN vs LilyGo T-Connect | Feature | Waveshare | LilyGo T-Connect | -| ------- | --------- | ---------------- | +|---------|-----------|------------------| | RS485 Ports | 1 (isolated) | Up to 3 (isolated) | | CAN Ports | 1 (isolated) | 1 (isolated) | | Built-in Termination | ✅ Yes (120Ω jumper-selectable) | ❌ No (external resistors required) |