36 KiB
YamBMS changelog
-
YamBMS 1.8.1 :
-
Set esphome
min_versionto2026.10.0 -
New documentation :
-
New documentation for contributors :
-
Updated HA dashboards
1.8.1with a markdown card for the new inverter link diagnostics (Inverter link protocol,Inverter battery mode,Note) and a system fault card -
Breaking change - New
Inverter brandselect and reworkedProtocolselect : selecting your inverter brand is enough, the protocol follows ; a protocol chosen explicitly still takes priority over the brand. Both selects are renamed, so their stored value is reset : the inverter link stays inactive until you select your inverter brand, see release note -
Removed the
YamBMS nameselect : the manufacturer name sent on CAN frame0x35Eis now derived from the protocol in use, which is what theAutomaticmode already did ; theGOODWE,SHEnergyandBYDnames are no longer selectable -
Breaking change - A package that uses a UART now declares it itself from its
*_uart_idvar : remove theboard_options_itf_uart_*.yamlincludes and theUART flow controlblock from your YAML, otherwise ESPHome reportsExpected integer, but cannot parse ${uart_baud_rate}. Each UART can only be used by one package : two packages on the same UART reportID uart_esp_1 redefined -
Baud rates are set in the
vars:of the package and keep their names ; packages that had none getbms_uart_baud_rate,sniffer_uart_baud_rateandshunt_uart_baud_rate, with the speed of the device as default -
New
uart_flow_control_pinvar on any package using a native ESP32 UART, which replaces theboard_options_itf_uart_flow_control.yamlinclude ; the_talk_pinpackages stay available for the rare setups that need them but are no longer shown in the examples -
WK2168 channels are now declared the same way :
board_options_itf_wk2168_spi.yamlorboard_options_itf_wk2168_i2c.yamlreplaces the PVbrain2 files in your YAML, theuartN_baudratesubstitutions anduart_hub_busare removed (writeuart_spi_3), andboard_options_itf_modbus_expander.yamlandshunt_combine_Victron_SmartShunt_UART_expander.yamlare removed -
Breaking change - A package that uses a CAN bus now declares its node itself : remove the
board_options_itf_canbus_*.yamlincludes from your YAML, otherwise ESPHome fails on the unresolved${canbus_bit_rate}, and addcanbus_platform(esp32_canormcp2515) to theyambms_canbus.yamlpackage and to the Deyetoppackage. A node declared by the board, or a second link on the same node, usescanbus_platform: 'external' -
The CAN bit rate is set with the new
canbus_bitratevar (default500kbps), which replacesesp32_canbus_bitrateandmcp2515_canbus_bitrate -
RS485 packages reorganised for the additional protocols to come : the file you include changes from
yambms_rs485_pylon.yamltoyambms_rs485.yaml, which now takes ars485_protocolvar (pylonorvoltronic) and includes the matching protocol implementation for you ; a node with several RS485 links on different UARTs can run a different protocol on each, one var per link ;yambms_rs485_pylon_web_server.yamlbecomesyambms_rs485_web_server.yamland includes the entry point itself : use it instead ofyambms_rs485.yaml, with the samevars:, see release note -
New diagnostic entities per inverter link :
Inverter link protocol(what the link is actually doing, e.g.Solis - CAN SMA),Inverter battery mode(how to configure the battery type on the inverter, keyed on brand and protocol so that forcing a protocol never displays a wrong instruction) andNote(what is specific to that brand and protocol) -
Renamed CAN protocol
PYLON 1.2toPYLON V1and RS485 protocolPylontechtoPYLON -
Schneider XW Pro : the extended 29-bit ACK is now handled automatically and the
canbus_extended_acksubstitution is removed - both the 11-bit and the 29-bit ACK are listened to at the same time, which the CAN component supports natively -
A link whose protocol is set to
Disabledno longer lights the fault LED : it is unregistered from the fault registry (state that the master mask and the health report both ignore) instead of being reported as failing, since it is a deliberate choice and not a communication loss ; a link left unconfigured still faults, on purpose -
Changing the inverter brand or protocol now restarts the CAN frames immediately instead of waiting for the next 30s retry tick, so the link comes up as soon as the selection is made
-
Fixed the RS485 link staying up with
Disabled: the proxy sensors kept their last value, so the Pylontech component went on answering the inverter with stale data and kept reporting its status as ON ; the sensors it checks are now invalidated when the protocol is off, which makes it stop answering and report the link as down -
Fixed the CAN bus not stopping when the protocol was set to
Disabledat runtime : the frame index kept its previous value and the last frame was re-emitted every 100 ms -
Fixed the reported communication bus and protocol being overwritten when a node declares several inverter links : each link now owns its slot, and the telemetry reports every link instead of the last one
-
Auto EOC : new
Auto EOC Start Hour/Auto EOC Start Minutedefine the charging window, which may cross midnight, and the target hour can be set from0to23(night charging from the grid) ; outside the window the status isWait: Starts at hh:mminstead ofStop: Target time passed, the default start0:00keeps the daylight behaviour -
Daily Charging Energy/Daily Discharging Energy(YamBMS and BMS) rounded to 10 Wh (0.01 kWh) instead of 1 Wh, to reduce the number of state changes recorded by Home Assistant -
Fixed YamBMS
Daily Charging Energy/Daily Discharging Energyjumping after a long period in the opposite direction : the unused power sensor was published as unknown, which ESPHome skips without advancing its time base, so the next reading was multiplied by the whole gap ;Battery Charging Power/Battery Discharging Powernow publish0 Won the unused side, as the shunt already did, and also when no BMS is combined -
The
Update serviceswitch is removed : the version check and the telemetry are now enabled separately with theyambms_update_serviceandyambms_telemetry_servicesubstitutions (both'true'by default), see Telemetry -
Telemetry no longer sends the MAC address but a salted SHA-256 hash of it, shown in the new
Node ID hashdiagnostic entity so that you can quote it for support ; the uptime is now sent in seconds -
The update and telemetry requests now go to
script.yambms.org -
Fixed
Uptimesometimes showing24855d 3h 14m 7safter boot, on the dashboard, the LVGL display and in the telemetry : the text sensor could format the uptime before it had a value, it is now published by its source -
Fixed
charging cyclesandtotal charging cycle capacitypublished as0after a reboot until the first BMS frame, which also landed in the Home Assistant long-term statistics : both are now unavailable during that time -
Auto CCL : the max cell voltage used by the curve is now smoothed with a time-based moving average (
auto_ccl_max_cell_v_tau, default30s,0disables), which stops the requested CCL swinging between about 8 A and 45 A near the top of charge ; a reading more thanauto_ccl_max_cell_v_guard(default5mV) above the average still cuts the current at once -
Auto CCL : new
auto_ccl_min_current(default1A), Auto CCL never requests less, including above the end of its curve ; other limits can still request 0 A -
A BMS reporting a charge (CCL) or discharge (DCL) limit of
0 Anow stays combined : a full battery at 0 A CCL, or an empty one at 0 A DCL, no longer drops out of the capacity, SoC and totals ; this applies to all BMS models, a limit not received yet still keeps the BMS uncombined -
Deye CAN : the battery power sensors now follow
bms_update_intervalinstead of updating every 60s -
Fixed sensors
device_class/state_classthat Home Assistant reported or handled wrongly : power sensors in W declared ascurrent(BASEN RS485, DEYE CAN module), Ah sensors carrying a class that does not accept Ah (BASEN RS485, DEYE CAN, JK RS485 Display, Modbus client), DEYE battery capacity moved fromtotal_increasingtomeasurement -
Fixed PACE BMS compilation with ESPHome 2026.9 / 2026.10
-
Fixed the Waveshare ESP32-S3 Touch-LCD 4.3, 4.3B and 7 boards failing validation on ESPHome 2026.10 with
Pin 2 is used in multiple places; the backlight stays under control of the LVGL designs -
New board
board_ESP32-P4_Elecrow-CrowPanel-Advanced-7-10.yaml(CrowPanel Advanced ESP32-P4) and new Blue Navy 1024x600 HA display design -
Fixed issue 332 YamBMS_RP_BMS_PACE_RS485_Modbus.yaml no longer compiles under esphome 2026-9-1
-
Fixed issue 335 PACE / DEYE packages: compile errors on ESPHome 2026.9–2026.10 + Deye power updated only every 60 s + full Deye excluded from combine
-
Merged PR 322 Add CrowPanel Advanced (ESP32-P4) board and Blue Navy 1024x600 HA display
-
Merged PR 329 Auto CCL smooths max cell voltage
-
Merged PR 331 Fix sensor device_class and state_class
-
Merged PR 336 Fix hub daily energy by publishing 0 W on the unused charge/discharge sign
-
Merged PR 337 Improve Deye support
-
Merged PR 338 Auto EOC 24h charging window
-
Merged PR 339 Round daily energy sensors to 10 Wh
-
-
YamBMS 1.8.0 :
- Set esphome
min_versionto2026.8.0 - New documentation :
- Updated HA dashboards
1.8.0for the new Cut-Off Cell Voltage, Charger Offset V., C-Rate and Auto CCL Current Taper entities - Rewritten Cut-Off / EOC charging logic : adds a current deadband (rejects sensor noise / low-solar current limiting) and a minimum SoC gate before Cut-Off can be declared, extends the cut-off confirmation delay from 60s to 180s to reject transient voltage readings, see release note
- New select
Cut-Off Cell Voltage: choose betweenMax Cell Voltage(default, conservative) andAverage Cell Voltage(consistent charge termination voltage for packs with a runner cell, requires Auto CVL and/or Auto CCL for cell protection) - New sliders
Max charge C-Rate/Max discharge C-Rate: the max charge/discharge current is now the lowest of the user slider, the BMS OCP safety margin, and battery capacity × C-Rate - Renamed
Inverter Offset V.toCharger Offset V.and allowed negative values (-1V to +1V) Requested Charge Voltage (CVL)calculation reworked : it is now built as a per-phase base target (Bulk→ bulk voltage,Float→ float voltage,Stop→ nominal voltage) plus a common set of offsets (Charger Offset V.,Auto CVL,Auto Floatand the newAuto Custom CVL, each0when its function is idle or disabled), instead of one hardcoded formula per phase ;Stopcharging voltage target changed fromRebulk V.to nominal voltage, so the pack no longer sits on the very threshold that decides when to rebulk.- Auto CVL : rewritten from a per-second template sensor to an interval lambda, now exposed as two sensors (
Auto CVLvalue +Auto CVL Delta) instead of one internal-only sensor ; it remains aBulk-only correction, theFloat/Stopslot of the new formula being left free for a future implementation - Auto Float : rewritten from a per-minute template sensor to an interval lambda, now exposed as two sensors (
Auto Float Voltagevalue +Auto Float Voltage Delta) ; no behavior change - Auto EOC : new 1-hour grace period holding the last computed current after target time passes (instead of releasing to maximum current), smoothed remaining-capacity estimate between BMS 1% SoC steps to remove current sawtoothing,
Stop SoCslider capped at 98% (100% could never trigger because SoC is clamped to 98% until end-of-charge) - New
Auto CCL Current Taperfunction : tapers CCL from a configurable knee voltage/C-Rate down to a bulk C-Rate, then holds a configurable balance current while at bulk or after EOC ; release hysteresis and Balance Current max are now scaled to cell count/battery capacity instead of flat constants, and a NaN guard prevents a spurious taper during the boot transient, see changelog - Fixed HA dashboards :
Auto CCL Current Tapercard's switch pointed to a non-existent entity id and never toggled - New substitutions
custom_ccl_derating_reason/custom_dcl_derating_reasonallowing a custom current-limiting source (e.g. added viayambms_custom.yaml) to report itself in the CCL/DCL derating reason sensor, and a similarAuto Custom CVLslot for voltage - Reworked Modbus timing options :
send_wait_timeis now a response timeout (default lowered from 2000ms to 200ms) and a newturnaround_timeoption was added; shared multi-node settings (yambms_config.yaml) updated accordingly - Improved PACE BMS Modbus : power is now computed from current × voltage instead of a raw register (fixes incorrect readings), improved offline detection
- Sensors (Total Voltage, Current, Power, SoC, Requested CVL/DVL/CCL/DCL, etc.) now publish as unavailable (
NaN) instead of0when no BMS is combined - Fixed
Installed Battery Capacityfrozen until reboot : the value was summed once per BMS at boot, so a BMS whose capacity was reconfigured at runtime kept contributing its old value ; each BMS now applies only the difference to the total, which still never shrinks when a BMS goes offline - Multi-inverter / multi-charger support : the requested CCL/DCL is now divided by the number of declared CAN/RS485 inverter interfaces, so several identical inverters/chargers sharing the same battery bank each receive their share of the limit instead of every unit requesting the full value, see documentation
- New
Combiner Stalldiagnostic sensor : reports which BMS or Shunt id the combiner pipeline is stuck on whenbms_id/shunt_idnumbering has a gap, instead of stalling silently with no combined values; added the newCombiner Stalldiagnostic row in dashboard - New
Fake Equalizing: BMS that balance their cells but never report a balancing flag had it hardcoded tofalse, so the Cut-Off timer ended the charge while the pack was still equalizing ; YamBMS now infers it, with no constant of its own - the voltage reference is the per-cell bulk setpoint (bulk voltage / cell count, so it follows the chemistry) and the spread reference isbms_balance_trigger_voltage, the threshold at which the pack's own balancer engages, which is 10 mV on a JK or a Seplos and 30 mV on an EG4, a pack reporting none at all simply never starting ; an external balancer keeps priority whenever one is online ; enabled by default for Seplos V3, Seplos V1/V2, EG4 LL v2 and JK RS485 DISPLAY, available for any other BMS, idea by @haysdb, see changelog bms_balance_trigger_voltageis now a var on EG4 LL v2 and JK RS485 DISPLAY, which hardcoded it : declare your unit's actual balancing threshold at import, as Seplos already required. EG4 keeps0.030as its default, JK RS485 DISPLAY moves from0.005to0.010to match the JK factory default - note that this value also feeds 'Auto CVL'- Updated EG4 LL-V2 component to v1.1.0 : fixes issue 7, some EG4 LL-V2 units intermittently answer with a CRC-valid response whose register data is entirely zero, which was published as a real reading and collapsed SoC / voltage / capacity for one poll cycle ; those blocks are now rejected and no longer refresh the online tracker
- PVbrain2 board split into two DevKitC-1 variants to follow the RGB LED / CAN TX pin swap between board revisions :
board_ESP32-S3_DevKitC-1_PVbrain2_LED-48.yaml(DevKitC-1 V1.0, LED on GPIO 48 and CAN TX on 38) andboard_ESP32-S3_DevKitC-1_PVbrain2_LED-38.yaml(V1.1, LED on GPIO 38 and CAN TX on 48), both including the commonboard_ESP32-S3_DevKitC-1_PVbrain2.yaml: include the one matching your board revision - New
loop_task_stack_sizeoption (8192/16384/32768) available on every board, to prevent stack overflow with a large number of BMS/entities, see documentation - Updated default PSRAM options for ESP-IDF 5.5+, see documentation
- Fixed incorrect Max/Min Cell Voltage scaling (×100 instead of ×1000) sent on the CAN bus for the Deye PCS protocol
secrets.yamltemplate renamed tosecrets_example.yaml(copy it to your own gitignoredsecrets.yaml, as documented in Installation_procedure.md)- Fixed a reboot every 6h on networks that filter the ESP32 outbound traffic (port 80 or DNS blocked) : the update and telemetry requests blocked the device long enough to trigger the watchdog ; requests now time out after 3s, the first one waits 5min after boot, and the services stop until the next reboot after 3 failed attempts
- Added
KS BMSBLE support, fixed issue 151 [ADD] Requesting KS BMS support - JK BLE : BMS alarms are now taken into account through the new
errors_bitmask_hexof the JK BLE component, instead of always reporting no alarm - Web server authentication switched to
digest - Fixed the
brightness not supportedwarning logged on every status LED change on boards with a single-colour LED ;rgb_orderreplaced bychannel_colorsin the board files (deprecated by ESPHome, removed in 2027.3.0), to report in your own board file if you have one - CAN frame logs moved from
INFOtoDEBUGlevel - Merged PR 308 Check if Auto SoC Limit has reached its target
- Merged PR 303 Auto CCL Current Taper
- Merged PR 290 Add grace period to Auto EOC
- Set esphome
-
YamBMS 1.7.0 :
- Partial rewrite of
yambms_coreand merging of C++ code into a single lambda in several stages with increased datas control. - Added LVGL display dashboard for Waveshare Touch-LCD 4.3" and 7" (Blue Navy 800x480 design)
- Fixed issue 10 Sending CAN bus data before the end of the combination process
- Fixed issue 154 Add
Enerkey Balancersbalance stop diff voltage setting (register 0x1A) - Fixed issue 160 The SOH sensor is interpreted as a battery percentage
- Fixed issue 182 Compliance of Auto functions for YamBMS 1.7.0
- Fixed issue 268 [Add an option] The inverter is not sending ACK CAN ID 0x305
- Fixed issue 282 JK errors_bitmask has been removed
- Merged PR 281 Add WS Touch-LCD-4.3B board
- Merged PR 261 Add LilyGo T-Connect Pro Lite board (without screen)
- Merged PR 259 Add support for Rebulk Days
- Merged PR 258 Auto EOC: Factor in Auto SoC Limit for battery capacity calculation
- Merged PR 255 Add support for Auto SoC Limit
- Merged PR 236 Switch to VictronMPPT-ESPHOME fork
- Merged PR 235 Basen: Add "Enable communication" switch
- Merged PR 200 Add M5Stack Tab5 with LVGL display
- Merged PR 199 Add Ecoworthy BMS integration for YamBMS
- Merged PR 194 Component Fault Registry & Advanced LED Control
- Merged PR 178 Basen BMS: Add heating control
- Merged PR 170 Add Freenove S3 board
- Merged PR 162 PACE Sensor Fixes
- Merged PR 158 Automatically disable shunt when connected BMSs are going offline
- Partial rewrite of
-
YamBMS 1.6.0 :
- New dashboards
1.6.0 - Added
iBMS V3.3board - Updated
JK-PBreadme with V19 warning and SoC 100% reset solution 1 and 2 - Added board option
UART flow controlallows you to activate atalk_pinfor the UART of your choice (e.g. WS-RS485-CAN) - Added AtomS3 GPIOs for
Atomic RS485 base(uart_esp_3) - Disabled the
reboot_timeoutafter 15 minutes in case of WiFi unavailability - New
Hardware highlighteddocumentation (LilyGo / Waveshare / M5Stack) - New readme for LilyGo T-Connect, WS RS485-CAN and M5Stack AtomS3 boards
- Improved documentation.
- Fixed issue 83 Add esphome-pace-bms
- Fixed issue 94 Multi-BMS Seplos V3 don't work
- Fixed issue 96 Improve the SoC returned at the end of discharge
- Fixed issue 100 Improve the BMS Seplos V1 V2 examples
- Fixed issue 102 Improve Remaining Capacity when using a shunt
- Added issue 106 [FEATURE REQUEST] Temperature-based current limiting
- Fixed issue 108 [WARNING] esphome::select::Select::state` is deprecated
- Fixed issue 122 Adjust
bms_namein all example YAML to something unique - Fixed issue 128 Align the names of the shunt entities
- Fixed issue 142 Maximum capacity needs to be increased for
JK_RS485BMS - Merged PR 76 Add
Auto EOCfunction - Merged PR 82 Add support for external balancer
- Merged PR 85 Adding
EG4 LLV2BMS - Merged PR 97 Add
Basen controllerversion with talk/flow control pin - Merged PR 99 Basen: Use new binary sensors for charging/discharging
- Merged PR 112 Adding
FLIP_C3board - Merged PR 117 Round requested charge/discharge current to nearest integer
- Change PR 119 Updated
Powergauge (-10kW to 10kW) - Merged PR 133 Add
Studer XTM-4000to supported inverters - Merged PR 142 Sub device support
- Merged PR 143 Improved
Cut-Off charginglogic equation and documentation - Merged PR 147 Improved
CCL,DCLandTemp-basedcurrent control - Merged PR 155 Update temperature sensor filters to reduce noise
- New dashboards
-
YamBMS 1.5.8 :
- New Dashboards
1.5.8compatible withCANBUSandRS485inverter communication protocol - Added BMS
SEPLOS V3(beta) - Added YamBMS
Web Server v3 - Added
WiFi AP WiFi APandWeb Servercredentials centralized insecrets.yaml- Added
WT32-ETH01board - Fixed issue 8 ETH01-EVO board - Davicom DM9051 SPI Ethernet Controller is now integrated in esphome
2025.7 - Fixed issue 24 [JK-PB] SoC never reaches 100%
- Fixed issue 63 [JK RS485 component] Fix ._SCHEMA deprecations
- Merged PR 67 Add options to restrict max. charge and discharge current
- Merged PR 72 Add Pylontech RS485 inverter protocol
- Merged PR 74
PYLON RS485link status, Heartbeat and Requested Force Charge - Merged PR 75 Round
Auto CCL/Auto DCLvalues - Merged PR 77
PYLON RS485prevent stale data on BMS disconnect - Merged PR 80 BMS Modbus client: Return 0 when not online
- Merged PR 81 Fix balance trigger voltage for Basen and Deye
- New Dashboards
-
YamBMS 1.5.7 :
- Adapted the default
min/maxvalues for theFloatslider - Merged PR 53 Add feature
Auto Float Voltage - New dashboard for
Auto Float Voltagefunction - Defining
state_classfor all YamBMS sensors - Set esphome
min_versionto2025.6.0 - Fixed: change
Charge StatustoBulkwhenForce Chargeis requested - Merged PR 70 Dashboards compatible with
HA 2025.7 - Merged PR 70 Dashboard
max/mincell voltage in color using macro - Removed all special characters in entities name + dashboards correction
- Adapted the default
-
YamBMS 1.5.6 :
- Fixed issue 58 Compilation problem with
esphome 2025.5.0 - Fixed issue 55 New CPU frequency option
- Fixed issue 65 JBD Circular dependency error
- Fixed issue 35 BMS Charging Cycles Offset
- Merged PR 51 Support for RP2040 RPi Pico
- Merged PR 56 Add support for Basengreen BMS
- Merged PR 60 Fixes for new ESPHome and add of BMS Cycle Count offset
- Merged PR 61 Set Modbus BMS values to 0 when BMS goes offline
- New
board_ESP32-S3_Touch-LCD-4.3.yamlboard - New
board_ESP32-S3_Touch-LCD-7.yamlboard - New
board_ESP32-S3_YBoard_DJK.yamlboard - New
board_RP2040_RPi_Pico.yamlboard
- Fixed issue 58 Compilation problem with
-
YamBMS 1.5.5 :
- New
main.yamlwith LP (local packages) and RP (remote packages) versions - New
board.yamlwith modular UART/CAN interfaces - The name of the JK
bms.yamlis no longer linked to a specific model - SoC calculation is now based on remaining capacity for more accuracy (BMS only) issues #39
- SoH calculation is moved to BMS level (for those who do not provide this information)
- Improvement of the Victron SmartShunt doc issues #38
- New
-
YamBMS 1.5.4 :
- New low SoC corrected at each BMS level (the corrected SoC is the one transmitted to YamBMS)
- New BMS dashboard
- New end of charge logic at each BMS level, the charge switch turns off when the cells are equalized (disabled by default)
- Fixed
errors_bitamskfor JK-PB RS485, test OK with YamBMS (forked component)
-
YamBMS 1.5.3 :
- Broadcasting JK-PB settings to all BMS set to OFF by default
- Reorganizing the
boardfolder and YAMLs (device_base.yaml moved to board.yaml) device_base.yamlshould no longer be part ofYamBMS_main.yaml- New
RGB LED statuslight effects (red, green, blue, cyan) as anoptionspackages forboard.yaml - Increased CPU frequency to
240Mhzas anoptionspackages forboard.yaml - Added
ESP32 Generic,LilyGo T-CAN485,LilyGo T-ConnectandXIAOboards - Fixed SoC logic (low SoC will be detected at BMS level and no longer at YamBMS level)
- Simplified combination logic (removal of the combine switch) + dashboard update
- Check
Battery Capacityis> 0before combining info (see issue #14) - Improved alarm logic with a common
YamBMS errors bitmaskfor all BMS models (see OTP vs UTP bug reported by @ChrisG) - Added PR #7547 regarding publishing entities via the API
- Removed
captive_portalbecause it increases theloop timetoo much PSRAMwill no longer be enabled by default as this has a bad impact onBLE BMS
-
YamBMS 1.5.2 :
- Added shunt
Online Statusbinary_sensor - Shunt combine condition based on the new binary_sensor
Online Status - Logger
baud_rate: 0by default (frees the 3rd UART and avoids some bugs like "WK2168 with canbus" or "BLE client with RS485 modbus") - Changed names of
bmsandshuntYAMLs for modbusmulti-nodesolution - Added shared configuration file to simplify main YAML (centralization of parameters)
- Simplification (fewer options) when importing
BMS / ShuntYAMLs - New
multi-nodesolution usingRS485 modbusto communicate information to YamBMS - New board
espBerrywith2-CH-CAN HAT
- Added shunt
-
YamBMS 1.5.1 :
- The conditions for
combiningBMS and thecharginganddischarginginstructions no longer have any relation with theerrors_bitmasksensor, the new system relies on the three binary_sensoronline status,charging allowedanddischarging allowedbeing linked to the status of alarms and switches. - The BMS combination procedure has been completely rewritten.
- Improved structure and ID names of
bms.yaml. - The
yambms.yamlandyambms_combine.yamlglobal variable names have been changed for better code reading. - Improved code regarding the CAN bus
esp_lightstatus for boards without integrated LED. - New
Atom S3Rboard andSmartshunt BLEshunt. - New
JBD,Seplos V1 V2,JK-B RS485(display port) andFAKEBMS. - New
YamBMS DEMOYAML and firmware offered to test and discover howYamBMSworks. - New management of temperature sensors (no longer limited to two sensors).
- @Der_Hannes fixed the AtomS3
black screenissue (with esphome > 2024.7.3) and developed new code for display management based on the ili9xxx platform. Auto CCL/DCLfunctions have been fixed to work withJK-PBandnew JK-BBMS, see this issue.- The
UVPRandOVPRsensors are no longer used and replaced byUVPandOVPto ensure operation with all BMS. - @txubelaxu fixed a bug in the
JK-PB RS485component that could cause a false battery voltage value to be sent, see this issue. - Improved documentation, added a
HowToto create its main YAML, warning about galvanic isolation.
- The conditions for
-
CANBUS 2.3.7 : If there is no response from the inverter, the time before a new communication test has been reduced from
120sto60s, added Victron0x372nbr. of modulesblocking charge/discharge. -
YamBMS 1.4.5 : Changed the way to configure WiFi/Ethernet network, added
ESP32-C3 ETH01-EVOethernet board, reduction of the number of YAML bms files, UARTrx_buffer_sizeis set to512by default for JK-B and JK-PB, new JK-BMS BLE sensors (last commits of @syssi) and new BLEstandardversion -
CANBUS 2.3.6 : Sending CAN frames stops immediately if there are no combined BMS
-
YamBMS 1.4.4 : Multi-shunt support, Simplified and new YamBMS option
battery chemistry, slidermin/maxvalues are automatically configured based on the battery chemistry and cell count, addedYamBMS Fallback Hotspot, added YamBMSUpdate service, added PVbrain2 and Atom Matrix board, added PSRAM settings YAML (not enabled by default), new MIN/MAX temperature sensor, added DC current icon, fixed dual sensorCell UVPR (MAX)bug, Improvedcombinecode, Breaking change : Atom S3GPIOs 1 and 2reversed -
CANBUS 2.3.5 : New MIN/MAX temperature / sensor ID, Improved Victron protocol (online/offline battery modules, installed/available battery capacity)
-
CANBUS 2.3.4 : Fixed bug of canbus link validation without inverter connected
-
YamBMS 1.4.3 : Added Victron and Junctek KH-F
Shuntsupport andRequested Force Chargefunction based onSoC start/stop, newTotal Daily Energysensors -
CANBUS 2.3.3 : Added
AutomaticBMS name selection andRequested Force ChargeBit 3/4/5 (PYLON 0x35C) -
CANBUS 2.3.2 : Added
LuxPowerprotocol with updatedcan_id0x355, 0x356, 0x359 and 0x35C -
CANBUS 2.3.1 : Improved the procedure for sending canbus frames with reduced loop time, rewritten of the canbus link validation code and added
Inverter Heartbeat Monitoringfunction -
YamBMS 1.4.2 : Added new
Auto CVL Boost V.andRebulk SoCfunctions, new debug.yaml for ESP32 and ESP32-S3, improved code and comments -
YamBMS 1.4.1 : Rewriting of the alarm system, bug fixes and improvement of the charging logic (new status
Cut-Off), icon allocation for each sensor, UART and CANBUS!extend ${vars}, New sensorYamBMS Delta Cell V., ImprovedBattery SOClogic -
YamBMS 1.3.2 : New var
yambms_cell_count, the BMS charge or discharge switches can be activated separately without causing the decombination of the BMS, newminimalversion of the BMS YAML in order to reduce the loop time -
YamBMS 1.3.1 : First multi-BMS version named
YamBMS