9.3 KiB
9.3 KiB
YamBMS - Supported devices
Supported BMS
JKBMS (BLE / UART / RS485)JBDBMS (BLE / UART)Seplos V1 V2 V3BMS (RS485)PACEBMS (RS485)BASENBMS (RS485)DEYEBMS (CAN)EcoworthyBMS (RS485)KSBMS (BLE)
Note: other BMS brands already integrated with ESPhome can be added easily.
Supported shunt
Victron Smartshunt(UART)Victron Smartshunt(BLE)Junctek KH-F(UART / RS485)
Note: other Shunt brands already integrated with ESPhome can be added easily.
Supported balancers
GW-24S4EB: NEEY/Heltec 4A Smart Active Balancer)(BLE)GW-24S4EB: NEEY 4A Smart Active Balancer 4th generation)(BLE)EK-24S15EB: (NEEY 15A Smart Active Balancer)(BLE)EK-24S10EB: (NEEY 10A Smart Active Balancer)(BLE)
Note: other Balancer brands already integrated with ESPhome can be added easily.
Supported MCU
This project works with various ESP32 variants and also with the Raspberry Pi Pico (RP2040).
Note that merging data from multiple BMS, balancers and shunts is resource-intensive, so I highly recommend a board based on the ESP32-S3 with PSRAM.
| AtomS3 Lite | AtomS3 | AtomS3R (8MB PSRAM) |
|---|---|---|
![]() |
![]() |
![]() |
| LilyGo T-CAN485 (ESP32) | LilyGo T-Connect (ESP32-S3) | Waveshare ESP32-S3-RS485-CAN |
|---|---|---|
![]() |
![]() |
![]() |
| ESP32 DevKit-V1 | ESP32-S3 DevKitC-1 | ESP32-C3 ETH01-EVO |
|---|---|---|
![]() |
![]() |
![]() |
| Olimex ESP32-EVB | espBerry + Waveshare 2-CH CAN HAT |
|---|---|
![]() |
![]() |
Supported CAN bus transceiver
Note: some inverters only accept a CAN bus at 3.3V in this case please choose the SN65HVD230 chip.
| TJA1050 (5V) | TJA1051T (5V) | SN65HVD230 (3V3) |
|---|---|---|
![]() |
![]() |
![]() |
| M5Stack Atomic CAN Base (isolated) | M5Stack CAN Unit (isolated) | MCP2515 (5V) |
|---|---|---|
![]() |
![]() |
![]() |
Supported RS485 transceiver
| M5Stack RS485 Unit (isolated) | RS485 isolated board (high speed dual) | RS485 Two-way Converter |
|---|---|---|
![]() |
![]() |
![]() |
Supported inverters
Inverters supporting CAN PYLON/Goodwe/SMA/Victron Low Voltage protocol should work, check your inverter manual to confirm.
The following are confirmed and known to work:
| Brand | Model | Inverter bat. mode | CAN/RS485 protocol | Remarks | Reported by |
|---|---|---|---|---|---|
| Deye | SUN-3.6K-SG03LP1-EU | Lithium 00 | CAN : PYLON 1.2 | --- | @Der_Hannes |
| Deye | SUN-5K-SG03LP1-EU | Lithium 00 | CAN : PYLON 1.2 | --- | @vdiex, @arzaman, @widget4145 |
| Deye | SUN-6K-SG03LP1-EU | Lithium 00 | CAN : PYLON 1.2 | --- | @Sleeper85, @Imanol82 |
| Deye | SUN-12K-SG04LP3-EU | Lithium 00 | CAN : PYLON 1.2 | --- | @lucize, @luckylinux, @virus100b, @b1ggi |
| Goodwe | GW5048-ES | --- | CAN : PYLON V2 | --- | @jirdol |
| Goodwe | GW5000S-BP | Goodwe LX U5.4-L | CAN : PYLON V2 | --- | @Uksa007, @OselDusan7 |
| Goodwe | GW3600S-BP | --- | CAN : PYLON V2 | --- | @OselDusan7 |
| Sofar | ME 3000-SP | --- | --- | --- | @starman |
| Sofar | HYD 3600-ES | Automatic | CAN : PYLON 1.2 | A 120 Ohm resistor had to be added on the Sofar side. | @chaosnature |
| Sofar | HYD 5000-ES | --- | --- | --- | @Paulfrench35 |
| Sofar | HYD 5000-EP | --- | --- | --- | @tonystrullu |
| Growatt | SPF 5000ES | CAN L52 | CAN : PYLON 1.2 | --- | @Paulfrench35, @cjdell, @cinusik |
| Solis | RHI-3.6K-48ES-5G | Pylon LV / AoBo | CAN : PYLON V2 / SMA | CAN transceiver 3V3 required (SN65HVD230) for Pylon LV mode. | @cjdell, @MrPabloUK |
| Solis | S5-EH1P4.6K-L | Pylon LV | CAN : PYLON V2 | CAN transceiver 3V3 required (SN65HVD230). | @Baker0052 |
| Solis | S5-EH1P6K-L | AoBo | CAN : SMA | --- | @MrPabloUK |
| Solis | RHI-3K-48ES | AoBo | CAN : SMA | --- | @chaosnature |
| LuxPower | LXP SNA 5K | Lithium 6 | CAN : LuxPower | --- | @shvmm, @yur43 |
| LuxPower | LXP-LB-US 10K | Lithium 6 | CAN : LuxPower | --- | @Henny101 |
| EG4 | 6000XP | Lithium 2 / Lithium 6 | CAN : PYLON 1.2 / LuxPower | --- | @ChrisG, @SGB |
| EG4 | 12000XP | Lithium 6 | CAN : LuxPower | --- | @andrewfraley |
| EG4 | 18kPV | Lithium 6 | CAN : LuxPower | --- | @Maintman |
| Victron | Multiplus 24/1200/25-16 | CAN-bus BMS LV (500 kbit/s) | CAN : Victron | Plugged into Cerbo CAN port (must use supplied Victron terminator in the other port). | @dmsims |
| Victron | MultiPlus-II 48/10000/140 | CAN-bus BMS LV (500 kbit/s) | CAN : Victron | --- | @cali-clim, @20after4 |
| MidNite Solar | MN15-12KW-AIO | PYLON | CAN : PYLON 1.2 | --- | @goldserve, @jahyde |
| SRNE | HESP48120U200-H | UZE | CAN : PYLON V2 | Most PYLON-based protocols show same results. Inverter does not work in PYLON mode, UZE works. Incorrect temp reported. | @ogremustcrush |
| Studer | XTM-4000 | Pylontech | CAN : PYLON V2 | DIP Switch in Xcom-CAN: 11000110 (1 to 8, ON==1). | @kolins-cz |
| Schneider | XW Pro 6848 NA | Voltage Control Li-Ion | CAN : PYLON V2 | Requires enabling the CAN bus option canbus_extended_ack: to true. |
@AGDorsum, @ngustas |
| SMA | Sunny Island | --- | --- | --- | --- |



















