Files
esphome-yambms/documents/README/Supported_devices.md
T
2026-11-08 23:08:33 +01:00

9.3 KiB

YamBMS - Supported devices

Badge License: GPLv3 Badge Version GitHub stars GitHub forks GitHub watchers

Supported BMS

  • JK BMS (BLE / UART / RS485)
  • JBD BMS (BLE / UART)
  • Seplos V1 V2 V3 BMS (RS485)
  • PACE BMS (RS485)
  • BASEN BMS (RS485)
  • DEYE BMS (CAN)
  • Ecoworthy BMS (RS485)
  • KS BMS (BLE)

Note: other BMS brands already integrated with ESPhome can be added easily.

Supported shunt

  • Victron Smartshunt (UART)
  • Victron Smartshunt (BLE)
  • Junctek KH-F (UART / RS485)

Note: other Shunt brands already integrated with ESPhome can be added easily.

Supported balancers

  • GW-24S4EB: NEEY/Heltec 4A Smart Active Balancer) (BLE)
  • GW-24S4EB: NEEY 4A Smart Active Balancer 4th generation) (BLE)
  • EK-24S15EB: (NEEY 15A Smart Active Balancer) (BLE)
  • EK-24S10EB: (NEEY 10A Smart Active Balancer) (BLE)

Note: other Balancer brands already integrated with ESPhome can be added easily.

Supported MCU

This project works with various ESP32 variants and also with the Raspberry Pi Pico (RP2040). Note that merging data from multiple BMS, balancers and shunts is resource-intensive, so I highly recommend a board based on the ESP32-S3 with PSRAM.

AtomS3 Lite AtomS3 AtomS3R (8MB PSRAM)
LilyGo T-CAN485 (ESP32) LilyGo T-Connect (ESP32-S3) Waveshare ESP32-S3-RS485-CAN
ESP32 DevKit-V1 ESP32-S3 DevKitC-1 ESP32-C3 ETH01-EVO
Olimex ESP32-EVB espBerry + Waveshare 2-CH CAN HAT

Supported CAN bus transceiver

Note: some inverters only accept a CAN bus at 3.3V in this case please choose the SN65HVD230 chip.

TJA1050 (5V) TJA1051T (5V) SN65HVD230 (3V3)
M5Stack Atomic CAN Base (isolated) M5Stack CAN Unit (isolated) MCP2515 (5V)

Supported RS485 transceiver

M5Stack RS485 Unit (isolated) RS485 isolated board (high speed dual) RS485 Two-way Converter

Supported inverters

Inverters supporting CAN PYLON/Goodwe/SMA/Victron Low Voltage protocol should work, check your inverter manual to confirm.

The following are confirmed and known to work:

Brand Model Inverter bat. mode CAN/RS485 protocol Remarks Reported by
Deye SUN-3.6K-SG03LP1-EU Lithium 00 CAN : PYLON 1.2 --- @Der_Hannes
Deye SUN-5K-SG03LP1-EU Lithium 00 CAN : PYLON 1.2 --- @vdiex, @arzaman, @widget4145
Deye SUN-6K-SG03LP1-EU Lithium 00 CAN : PYLON 1.2 --- @Sleeper85, @Imanol82
Deye SUN-12K-SG04LP3-EU Lithium 00 CAN : PYLON 1.2 --- @lucize, @luckylinux, @virus100b, @b1ggi
Goodwe GW5048-ES --- CAN : PYLON V2 --- @jirdol
Goodwe GW5000S-BP Goodwe LX U5.4-L CAN : PYLON V2 --- @Uksa007, @OselDusan7
Goodwe GW3600S-BP --- CAN : PYLON V2 --- @OselDusan7
Sofar ME 3000-SP --- --- --- @starman
Sofar HYD 3600-ES Automatic CAN : PYLON 1.2 A 120 Ohm resistor had to be added on the Sofar side. @chaosnature
Sofar HYD 5000-ES --- --- --- @Paulfrench35
Sofar HYD 5000-EP --- --- --- @tonystrullu
Growatt SPF 5000ES CAN L52 CAN : PYLON 1.2 --- @Paulfrench35, @cjdell, @cinusik
Solis RHI-3.6K-48ES-5G Pylon LV / AoBo CAN : PYLON V2 / SMA CAN transceiver 3V3 required (SN65HVD230) for Pylon LV mode. @cjdell, @MrPabloUK
Solis S5-EH1P4.6K-L Pylon LV CAN : PYLON V2 CAN transceiver 3V3 required (SN65HVD230). @Baker0052
Solis S5-EH1P6K-L AoBo CAN : SMA --- @MrPabloUK
Solis RHI-3K-48ES AoBo CAN : SMA --- @chaosnature
LuxPower LXP SNA 5K Lithium 6 CAN : LuxPower --- @shvmm, @yur43
LuxPower LXP-LB-US 10K Lithium 6 CAN : LuxPower --- @Henny101
EG4 6000XP Lithium 2 / Lithium 6 CAN : PYLON 1.2 / LuxPower --- @ChrisG, @SGB
EG4 12000XP Lithium 6 CAN : LuxPower --- @andrewfraley
EG4 18kPV Lithium 6 CAN : LuxPower --- @Maintman
Victron Multiplus 24/1200/25-16 CAN-bus BMS LV (500 kbit/s) CAN : Victron Plugged into Cerbo CAN port (must use supplied Victron terminator in the other port). @dmsims
Victron MultiPlus-II 48/10000/140 CAN-bus BMS LV (500 kbit/s) CAN : Victron --- @cali-clim, @20after4
MidNite Solar MN15-12KW-AIO PYLON CAN : PYLON 1.2 --- @goldserve, @jahyde
SRNE HESP48120U200-H UZE CAN : PYLON V2 Most PYLON-based protocols show same results. Inverter does not work in PYLON mode, UZE works. Incorrect temp reported. @ogremustcrush
Studer XTM-4000 Pylontech CAN : PYLON V2 DIP Switch in Xcom-CAN: 11000110 (1 to 8, ON==1). @kolins-cz
Schneider XW Pro 6848 NA Voltage Control Li-Ion CAN : PYLON V2 Requires enabling the CAN bus option canbus_extended_ack: to true. @AGDorsum, @ngustas
SMA Sunny Island --- --- --- ---