Files
esphome-yambms/documents/README/Changelog.md
T
2026-06-29 01:17:11 +02:00

17 KiB
Raw Blame History

YamBMS changelog

Badge License: GPLv3 Badge Version GitHub stars GitHub forks GitHub watchers

  • YamBMS 1.7.0 :

    • Partial rewrite of yambms_core and merging of C++ code into a single lambda in several stages with increased datas control.
    • Added LVGL display dashboard for Waveshare Touch-LCD 4.3" and 7" (Blue Navy 800x480 design)
    • Fixed issue 10 Sending CAN bus data before the end of the combination process
    • Fixed issue 154 Add Enerkey Balancers balance stop diff voltage setting (register 0x1A)
    • Fixed issue 160 The SOH sensor is interpreted as a battery percentage
    • Fixed issue 182 Compliance of Auto functions for YamBMS 1.7.0
    • Fixed issue 268 [Add an option] The inverter is not sending ACK CAN ID 0x305
    • Fixed issue 282 JK errors_bitmask has been removed
    • Merged PR 281 Add WS Touch-LCD-4.3B board
    • Merged PR 261 Add LilyGo T-Connect Pro Lite board (without screen)
    • Merged PR 259 Add support for Rebulk Days
    • Merged PR 258 Auto EOC: Factor in Auto SoC Limit for battery capacity calculation
    • Merged PR 255 Add support for Auto SoC Limit
    • Merged PR 236 Switch to VictronMPPT-ESPHOME fork
    • Merged PR 235 Basen: Add "Enable communication" switch
    • Merged PR 200 Add M5Stack Tab5 with LVGL display
    • Merged PR 199 Add Ecoworthy BMS integration for YamBMS
    • Merged PR 194 Component Fault Registry & Advanced LED Control
    • Merged PR 178 Basen BMS: Add heating control
    • Merged PR 170 Add Freenove S3 board
    • Merged PR 162 PACE Sensor Fixes
    • Merged PR 158 Automatically disable shunt when connected BMSs are going offline
  • YamBMS 1.6.0 :

    • New dashboards 1.6.0
    • Added iBMS V3.3 board
    • Updated JK-PB readme with V19 warning and SoC 100% reset solution 1 and 2
    • Added board option UART flow control allows you to activate a talk_pin for the UART of your choice (e.g. WS-RS485-CAN)
    • Added AtomS3 GPIOs for Atomic RS485 base (uart_esp_3)
    • Disabled the reboot_timeout after 15 minutes in case of WiFi unavailability
    • New Hardware highlighted documentation (LilyGo / Waveshare / M5Stack)
    • New readme for LilyGo T-Connect, WS RS485-CAN and M5Stack AtomS3 boards
    • Improved documentation.
    • Fixed issue 83 Add esphome-pace-bms
    • Fixed issue 94 Multi-BMS Seplos V3 don't work
    • Fixed issue 96 Improve the SoC returned at the end of discharge
    • Fixed issue 100 Improve the BMS Seplos V1 V2 examples
    • Fixed issue 102 Improve Remaining Capacity when using a shunt
    • Added issue 106 [FEATURE REQUEST] Temperature-based current limiting
    • Fixed issue 108 [WARNING] esphome::select::Select::state` is deprecated
    • Fixed issue 122 Adjust bms_name in all example YAML to something unique
    • Fixed issue 128 Align the names of the shunt entities
    • Fixed issue 142 Maximum capacity needs to be increased for JK_RS485 BMS
    • Merged PR 76 Add Auto EOC function
    • Merged PR 82 Add support for external balancer
    • Merged PR 85 Adding EG4 LLV2 BMS
    • Merged PR 97 Add Basen controller version with talk/flow control pin
    • Merged PR 99 Basen: Use new binary sensors for charging/discharging
    • Merged PR 112 Adding FLIP_C3 board
    • Merged PR 117 Round requested charge/discharge current to nearest integer
    • Change PR 119 Updated Power gauge (-10kW to 10kW)
    • Merged PR 133 Add Studer XTM-4000 to supported inverters
    • Merged PR 142 Sub device support
    • Merged PR 143 Improved Cut-Off charging logic equation and documentation
    • Merged PR 147 Improved CCL, DCL and Temp-based current control
    • Merged PR 155 Update temperature sensor filters to reduce noise
  • YamBMS 1.5.8 :

    • New Dashboards 1.5.8 compatible with CANBUS and RS485 inverter communication protocol
    • Added BMS SEPLOS V3 (beta)
    • Added YamBMS Web Server v3
    • Added WiFi AP
    • WiFi AP and Web Server credentials centralized in secrets.yaml
    • Added WT32-ETH01 board
    • Fixed issue 8 ETH01-EVO board - Davicom DM9051 SPI Ethernet Controller is now integrated in esphome 2025.7
    • Fixed issue 24 [JK-PB] SoC never reaches 100%
    • Fixed issue 63 [JK RS485 component] Fix ._SCHEMA deprecations
    • Merged PR 67 Add options to restrict max. charge and discharge current
    • Merged PR 72 Add Pylontech RS485 inverter protocol
    • Merged PR 74 PYLON RS485 link status, Heartbeat and Requested Force Charge
    • Merged PR 75 Round Auto CCL / Auto DCL values
    • Merged PR 77 PYLON RS485 prevent stale data on BMS disconnect
    • Merged PR 80 BMS Modbus client: Return 0 when not online
    • Merged PR 81 Fix balance trigger voltage for Basen and Deye
  • YamBMS 1.5.7 :

    • Adapted the default min/max values ​​for the Float slider
    • Merged PR 53 Add feature Auto Float Voltage
    • New dashboard for Auto Float Voltage function
    • Defining state_class for all YamBMS sensors
    • Set esphome min_version to 2025.6.0
    • Fixed: change Charge Status to Bulk when Force Charge is requested
    • Merged PR 70 Dashboards compatible with HA 2025.7
    • Merged PR 70 Dashboard max/min cell voltage in color using macro
    • Removed all special characters in entities name + dashboards correction
  • YamBMS 1.5.6 :

    • Fixed issue 58 Compilation problem with esphome 2025.5.0
    • Fixed issue 55 New CPU frequency option
    • Fixed issue 65 JBD Circular dependency error
    • Fixed issue 35 BMS Charging Cycles Offset
    • Merged PR 51 Support for RP2040 RPi Pico
    • Merged PR 56 Add support for Basengreen BMS
    • Merged PR 60 Fixes for new ESPHome and add of BMS Cycle Count offset
    • Merged PR 61 Set Modbus BMS values to 0 when BMS goes offline
    • New board_ESP32-S3_Touch-LCD-4.3.yaml board
    • New board_ESP32-S3_Touch-LCD-7.yaml board
    • New board_ESP32-S3_YBoard_DJK.yaml board
    • New board_RP2040_RPi_Pico.yaml board
  • YamBMS 1.5.5 :

    • New main.yaml with LP (local packages) and RP (remote packages) versions
    • New board.yaml with modular UART/CAN interfaces
    • The name of the JK bms.yaml is no longer linked to a specific model
    • SoC calculation is now based on remaining capacity for more accuracy (BMS only) issues #39
    • SoH calculation is moved to BMS level (for those who do not provide this information)
    • Improvement of the Victron SmartShunt doc issues #38
  • YamBMS 1.5.4 :

    • New low SoC corrected at each BMS level (the corrected SoC is the one transmitted to YamBMS)
    • New BMS dashboard
    • New end of charge logic at each BMS level, the charge switch turns off when the cells are equalized (disabled by default)
    • Fixed errors_bitamsk for JK-PB RS485, test OK with YamBMS (forked component)
  • YamBMS 1.5.3 :

    • Broadcasting JK-PB settings to all BMS set to OFF by default
    • Reorganizing the board folder and YAMLs (device_base.yaml moved to board.yaml)
    • device_base.yaml should no longer be part of YamBMS_main.yaml
    • New RGB LED status light effects (red, green, blue, cyan) as an options packages for board.yaml
    • Increased CPU frequency to 240Mhz as an options packages for board.yaml
    • Added ESP32 Generic, LilyGo T-CAN485, LilyGo T-Connect and XIAO boards
    • Fixed SoC logic (low SoC will be detected at BMS level and no longer at YamBMS level)
    • Simplified combination logic (removal of the combine switch) + dashboard update
    • Check Battery Capacity is > 0 before combining info (see issue #14)
    • Improved alarm logic with a common YamBMS errors bitmask for all BMS models (see OTP vs UTP bug reported by @ChrisG)
    • Added PR #7547 regarding publishing entities via the API
    • Removed captive_portal because it increases the loop time too much
    • PSRAM will no longer be enabled by default as this has a bad impact on BLE BMS
  • YamBMS 1.5.2 :

    • Added shunt Online Status binary_sensor
    • Shunt combine condition based on the new binary_sensor Online Status
    • Logger baud_rate: 0 by default (frees the 3rd UART and avoids some bugs like "WK2168 with canbus" or "BLE client with RS485 modbus")
    • Changed names of bms and shunt YAMLs for modbus multi-node solution
    • Added shared configuration file to simplify main YAML (centralization of parameters)
    • Simplification (fewer options) when importing BMS / Shunt YAMLs
    • New multi-node solution using RS485 modbus to communicate information to YamBMS
    • New board espBerry with 2-CH-CAN HAT
  • YamBMS 1.5.1 :

    • The conditions for combining BMS and the charging and discharging instructions no longer have any relation with the errors_bitmask sensor, the new system relies on the three binary_sensor online status, charging allowed and discharging allowed being linked to the status of alarms and switches.
    • The BMS combination procedure has been completely rewritten.
    • Improved structure and ID names of bms.yaml.
    • The yambms.yaml and yambms_combine.yaml global variable names have been changed for better code reading.
    • Improved code regarding the CAN bus esp_light status for boards without integrated LED.
    • New Atom S3R board and Smartshunt BLE shunt.
    • New JBD, Seplos V1 V2, JK-B RS485 (display port) and FAKE BMS.
    • New YamBMS DEMO YAML and firmware offered to test and discover how YamBMS works.
    • New management of temperature sensors (no longer limited to two sensors).
    • @Der_Hannes fixed the AtomS3 black screen issue (with esphome > 2024.7.3) and developed new code for display management based on the ili9xxx platform.
    • Auto CCL/DCL functions have been fixed to work with JK-PB and new JK-B BMS, see this issue.
    • The UVPR and OVPR sensors are no longer used and replaced by UVP and OVP to ensure operation with all BMS.
    • @txubelaxu fixed a bug in the JK-PB RS485 component that could cause a false battery voltage value to be sent, see this issue.
    • Improved documentation, added a HowTo to create its main YAML, warning about galvanic isolation.
  • CANBUS 2.3.7 : If there is no response from the inverter, the time before a new communication test has been reduced from 120s to 60s, added Victron 0x372 nbr. of modules blocking charge/discharge.

  • YamBMS 1.4.5 : Changed the way to configure WiFi/Ethernet network, added ESP32-C3 ETH01-EVO ethernet board, reduction of the number of YAML bms files, UART rx_buffer_size is set to 512 by default for JK-B and JK-PB, new JK-BMS BLE sensors (last commits of @syssi) and new BLE standard version

  • CANBUS 2.3.6 : Sending CAN frames stops immediately if there are no combined BMS

  • YamBMS 1.4.4 : Multi-shunt support, Simplified and new YamBMS option battery chemistry, slider min/max values ​​are automatically configured based on the battery chemistry and cell count, added YamBMS Fallback Hotspot, added YamBMS Update service, added PVbrain2 and Atom Matrix board, added PSRAM settings YAML (not enabled by default), new MIN/MAX temperature sensor, added DC current icon, fixed dual sensor Cell UVPR (MAX) bug, Improved combine code, Breaking change : Atom S3 GPIOs 1 and 2 reversed

  • CANBUS 2.3.5 : New MIN/MAX temperature / sensor ID, Improved Victron protocol (online/offline battery modules, installed/available battery capacity)

  • CANBUS 2.3.4 : Fixed bug of canbus link validation without inverter connected

  • YamBMS 1.4.3 : Added Victron and Junctek KH-F Shunt support and Requested Force Charge function based on SoC start/stop, new Total Daily Energy sensors

  • CANBUS 2.3.3 : Added Automatic BMS name selection and Requested Force Charge Bit 3/4/5 (PYLON 0x35C)

  • CANBUS 2.3.2 : Added LuxPower protocol with updated can_id 0x355, 0x356, 0x359 and 0x35C

  • CANBUS 2.3.1 : Improved the procedure for sending canbus frames with reduced loop time, rewritten of the canbus link validation code and added Inverter Heartbeat Monitoring function

  • YamBMS 1.4.2 : Added new Auto CVL Boost V. and Rebulk SoC functions, new debug.yaml for ESP32 and ESP32-S3, improved code and comments

  • YamBMS 1.4.1 : Rewriting of the alarm system, bug fixes and improvement of the charging logic (new status Cut-Off), icon allocation for each sensor, UART and CANBUS !extend ${vars}, New sensor YamBMS Delta Cell V., Improved Battery SOC logic

  • YamBMS 1.3.2 : New var yambms_cell_count, the BMS charge or discharge switches can be activated separately without causing the decombination of the BMS, new minimal version of the BMS YAML in order to reduce the loop time

  • YamBMS 1.3.1 : First multi-BMS version named YamBMS