9.0 KiB
YamBMS - JK-B BMS
Important
The most important thing for proper functioning of YamBMS is that the voltage of your BMS is well calibrated. YamBMS logic is based on the
min_cell_voltageandmax_cell_voltagevoltages of your BMS.
JK-B BMS overview
UART1 (GPS) port
The GPS port sometimes called RS485 is not an RS485 port but 3V3 UART-TTL port.
# UART-TTL GPS port on JK-BMS (4 pin, JST 1.25mm pitch)
┌─── ─────── ────┐
│ │
│ O O O O │
│GND RX TX VBAT│
└────────────────┘
│ │ │ └ VBAT is full battery voltage eg. 56V (possible to use it via an isolated DC-DC converter)
│ │ └──── TX to TTL-isolator AI (input)
│ └──────── RX to TTL-isolator AO (output)
└──────────── GND to TTL-isolator GND
The UART1 (labeled as GPS) socket of the BMS can be attached to any UART pins of the ESP32.
A hardware UART should be preferred because of the high baudrate (115200 baud).
The connector is called 4 pin JST with 1.25mm pitch.
JK-B BMS protocol
Historically it was not possible to change the protocol of the UART1 (GPS) port and the protocol used was 4G-GPS Remote module Common protocol V4.2 with the component esphome-jk-bms of @syssi.
If you cannot change the protocol of the UART1 (GPS) port you can only monitor one BMS per UART port of the ESP32, so a maximum of 3x BMS without adding a UART expander.
If you have a recent BMS, it is now possible to change the protocol of the UART1 (GPS) port and with the JK BMS RS485 Modbus V1.0 protocol you can assign an address (via JK app) to your BMS and monitor several of them from a single UART-RS485 connection in the same way as the JK-PB. To use this protocol and monitor all your BMS on a single RS485 bus you will need to add the UART to RS485 adapter sold by JK or another RS485 board of your choice.
Schematic and setup instructions
Caution
The
GNDof theJK-B GPS portis directly connected with theB-of your battery. Even if your BMS is in protection or stopped you can measure thefull voltagebetween thisGNDandB+. This therefore presents a risk ofbypassof the BMSP-and can be dangerous if the GND of your ESP32 is connected to the GND of your inverter or a measurement shunt for example. I therefore strongly advise you to achieve galvanic isolation between your ESP32 and theUART-TTLof theJK-B GPS port.
Galvanic isolation of the UART-TTL connection
Caution
Please read this page about setting up galvanic isolation of the
UART-TTLconnection.
Atom S3 (ESP32-S3)
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_atom-s3-lite.yaml file.
You need to import this YAML into the main YAML.
UART-TTL RS232-TTL CAN BUS
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│1 5│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│2 6│<RX-------RX>| CA-IS3050G |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │ | CAN |<---CAN L --->| |
│ │ 5V---->│5V 3V3| | | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Atom Lite (ESP32-PICO)
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_atom-lite.yaml file.
You need to import this YAML into the main YAML.
UART-TTL RS232-TTL CAN BUS
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│32 22│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│26 19│<RX-------RX>| CA-IS3050G |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │ | CAN |<---CAN L --->| |
│ │ 5V---->│5V 3V3| | | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Generic ESP32 DevKit V1 30 pin
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_esp32-devkit-v1.yaml file.
You need to import this YAML into the main YAML.
3V3 CAN bus
UART-TTL RS232-TTL CAN BUS (3V3)
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│17 22│<RX-------RX>| SN65HVD230 |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │<----GND---->| CAN |<---CAN L --->| |
│ │ 5V---->│VIN 3V3│<----3V3---->| | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
5V CAN bus
UART-TTL RS232-TTL CAN BUS (5V)
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│17 22│<RX--4K7--RX>| TJA1050 |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │<----GND---->| CAN |<---CAN L --->| |
│ │ 5V---->│VIN VIN│<----5V----->| | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Schematic with addition of the UART-TTL to RS485 adapter sold by Jikong
UART-TTL RS485 RS485-TTL RS232-TTL CAN BUS
┌──────────┐ ┌───────────┐ ┌────────┐ ┌─────────┐ ┌─────────┐ ┌──────────┐
│ │<----TX---->│Y JK Y│<A------A+>│ │<TX-----RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<----RX---->│W RS485 W│<B------B->│ RS485 │<RX-----TX>│17 22│<RX--4K7--RX>| TJA1050 |<---CAN H --->| Inverter |
│ │<----GND--->│B Adaptor B│<---GND--->│To 3.3V │<---GND--->| |<----GND---->| CAN |<---CAN L --->| |
│ │<----VBAT-->│R │ │ │<---3V3--->| ESP32 |<----5V----->| | | |
└──────────┘ └───────────┘ └────────┘ └─────────┘ └─────────┘ └──────────┘

