7.8 KiB
YamBMS - JK-B BMS UART Solution
External component
Schematic and setup instructions
Caution
The
GNDof theJK-B GPS portis directly connected with theB-of your battery. Even if your BMS is in protection or stopped you can measure thefull voltagebetween thisGNDandB+. This therefore presents a risk ofbypassof the BMSP-and can be dangerous if the GND of your ESP32 is connected to the GND of your inverter or a measurement shunt for example. I therefore strongly advise you to achieve galvanic isolation between your ESP32 and theUART-TTLof theJK-B GPS port.
Galvanic isolation of the UART-TTL connection
Caution
Please read this page about setting up galvanic isolation of the
UART-TTLconnection.
Atom S3 (ESP32-S3)
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_atom-s3-lite.yaml file.
You need to import this YAML into the main YAML.
UART-TTL RS232-TTL CAN BUS
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│2 5│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│1 6│<RX-------RX>| CA-IS3050G |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │ | CAN |<---CAN L --->| |
│ │ 5V---->│5V 3V3| | | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Atom Lite (ESP32-PICO)
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_atom-lite.yaml file.
You need to import this YAML into the main YAML.
UART-TTL RS232-TTL CAN BUS
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│26 22│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│32 19│<RX-------RX>| CA-IS3050G |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │ | CAN |<---CAN L --->| |
│ │ 5V---->│5V 3V3| | | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Generic ESP32 DevKit V1 30 pin
Caution
The diagram below does not show the galvanic isolation of the
UART-TTLconnection !
The GPIOs are preconfigured in the packages/board/board_esp32-devkit-v1.yaml file.
You need to import this YAML into the main YAML.
3V3 CAN bus
UART-TTL RS232-TTL CAN BUS (3V3)
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│17 22│<RX-------RX>| SN65HVD230 |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │<----GND---->| CAN |<---CAN L --->| |
│ │ 5V---->│VIN 3V3│<----3V3---->| | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
5V CAN bus
UART-TTL RS232-TTL CAN BUS (5V)
┌──────────┐ ┌──────────┐ ┌────────────┐ ┌──────────┐
│ │<TX------RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<RX------TX>│17 22│<RX--4K7--RX>| TJA1050 |<---CAN H --->| Inverter |
│ │<----GND--->│ ESP32 │<----GND---->| CAN |<---CAN L --->| |
│ │ 5V---->│VIN VIN│<----5V----->| | | |
└──────────┘ └──────────┘ └────────────┘ └──────────┘
Schematic with addition of the UART-TTL to RS485 adapter sold by Jikong
UART-TTL RS485 RS485-TTL RS232-TTL CAN BUS
┌──────────┐ ┌───────────┐ ┌────────┐ ┌─────────┐ ┌─────────┐ ┌──────────┐
│ │<----TX---->│Y JK Y│<A------A+>│ │<TX-----RX>│16 23│<TX-------TX>| | | |
│ JK-BMS │<----RX---->│W RS485 W│<B------B->│ RS485 │<RX-----TX>│17 22│<RX--4K7--RX>| TJA1050 |<---CAN H --->| Inverter |
│ │<----GND--->│B Adaptor B│<---GND--->│To 3.3V │<---GND--->| |<----GND---->| CAN |<---CAN L --->| |
│ │<----VBAT-->│R │ │ │<---3V3--->| ESP32 |<----5V----->| | | |
└──────────┘ └───────────┘ └────────┘ └─────────┘ └─────────┘ └──────────┘
JK-B BMS UART-TTL GPS port
The GPS port sometimes called RS485 is not an RS485 port but 3V3 UART-TTL.
# UART-TTL GPS port on JK-BMS (4 pin, JST 1.25mm pitch)
┌─── ─────── ────┐
│ │
│ O O O O │
│GND RX TX VBAT│
└────────────────┘
│ │ │ └ VBAT is full battery volatge eg 51.2V (possible to use it via an isolated DC-DC converter)
│ │ └──── TX to TTL-isolator AI (input)
│ └──────── RX to TTL-isolator AO (output)
└──────────── GND to TTL-isolator GND
The UART-TTL (labeled as GPS) socket of the BMS can be attached to any UART pins of the ESP.
A hardware UART should be preferred because of the high baudrate (115200 baud).
The connector is called 4 pin JST with 1.25mm pitch.
