YamBMS - Supported devices

Supported BMS
JK BMS (BLE / UART / RS485)
JBD BMS (BLE / UART)
Seplos V1 V2 V3 BMS (RS485)
PACE BMS (RS485)
BASEN BMS (RS485)
DEYE BMS (CAN)
Ecoworthy BMS (RS485)
KS BMS (BLE)
Note: other BMS brands already integrated with ESPhome can be added easily.
Supported shunt
Victron Smartshunt (UART)
Victron Smartshunt (BLE)
Junctek KH-F (UART / RS485)
Note: other Shunt brands already integrated with ESPhome can be added easily.
Supported balancers
GW-24S4EB: NEEY/Heltec 4A Smart Active Balancer) (BLE)
GW-24S4EB: NEEY 4A Smart Active Balancer 4th generation) (BLE)
EK-24S15EB: (NEEY 15A Smart Active Balancer) (BLE)
EK-24S10EB: (NEEY 10A Smart Active Balancer) (BLE)
Note: other Balancer brands already integrated with ESPhome can be added easily.
Supported MCU
This project works with various ESP32 variants and also with the Raspberry Pi Pico (RP2040).
Note that merging data from multiple BMS, balancers and shunts is resource-intensive, so I highly recommend a board based on the ESP32-S3 with PSRAM.
Supported CAN bus transceiver
Note: some inverters only accept a CAN bus at 3.3V in this case please choose the SN65HVD230 chip.
Supported RS485 transceiver
Supported inverters
Inverters supporting CAN PYLON/Goodwe/SMA/Victron Low Voltage protocol should work, check your inverter manual to confirm.
The following are confirmed and known to work:
| Brand |
Model |
Inverter bat. mode |
CAN/RS485 protocol |
Remarks |
Reported by |
| Deye |
SUN-3.6K-SG03LP1-EU |
Lithium 00 |
CAN : PYLON V1 |
--- |
@Der_Hannes |
| Deye |
SUN-5K-SG03LP1-EU |
Lithium 00 |
CAN : PYLON V1 |
--- |
@vdiex, @arzaman, @widget4145 |
| Deye |
SUN-6K-SG03LP1-EU |
Lithium 00 |
CAN : PYLON V1 |
--- |
@Sleeper85, @Imanol82 |
| Deye |
SUN-12K-SG04LP3-EU |
Lithium 00 |
CAN : PYLON V1 |
--- |
@lucize, @luckylinux, @virus100b, @b1ggi |
| Goodwe |
GW5048-ES |
--- |
CAN : PYLON V2 |
--- |
@jirdol |
| Goodwe |
GW5000S-BP |
Goodwe LX U5.4-L |
CAN : PYLON V2 |
--- |
@Uksa007, @OselDusan7 |
| Goodwe |
GW3600S-BP |
--- |
CAN : PYLON V2 |
--- |
@OselDusan7 |
| Sofar |
ME 3000-SP |
--- |
--- |
--- |
@starman |
| Sofar |
HYD 3600-ES |
Automatic |
CAN : PYLON V1 |
A 120 Ohm resistor had to be added on the Sofar side. |
@chaosnature |
| Sofar |
HYD 5000-ES |
--- |
--- |
--- |
@Paulfrench35 |
| Sofar |
HYD 5000-EP |
--- |
--- |
--- |
@tonystrullu |
| Growatt |
SPF 5000ES |
CAN L52 |
CAN : PYLON V1 |
--- |
@Paulfrench35, @cjdell, @cinusik |
| Solis |
RHI-3.6K-48ES-5G |
Pylon LV / AoBo |
CAN : PYLON V2 / SMA |
CAN transceiver 3V3 required (SN65HVD230) for Pylon LV mode. |
@cjdell, @MrPabloUK |
| Solis |
S5-EH1P4.6K-L |
Pylon LV |
CAN : PYLON V2 |
CAN transceiver 3V3 required (SN65HVD230). |
@Baker0052 |
| Solis |
S5-EH1P6K-L |
AoBo |
CAN : SMA |
--- |
@MrPabloUK |
| Solis |
RHI-3K-48ES |
AoBo |
CAN : SMA |
--- |
@chaosnature |
| LuxPower |
LXP SNA 5K |
Lithium 6 |
CAN : LuxPower |
--- |
@shvmm, @yur43 |
| LuxPower |
LXP-LB-US 10K |
Lithium 6 |
CAN : LuxPower |
--- |
@Henny101 |
| EG4 |
6000XP |
Lithium 2 / Lithium 6 |
CAN : PYLON V1 / LuxPower |
--- |
@ChrisG, @SGB |
| EG4 |
12000XP |
Lithium 6 |
CAN : LuxPower |
--- |
@andrewfraley |
| EG4 |
18kPV |
Lithium 6 |
CAN : LuxPower |
--- |
@Maintman |
| Victron |
Multiplus 24/1200/25-16 |
CAN-bus BMS LV (500 kbit/s) |
CAN : Victron |
Plugged into Cerbo CAN port (must use supplied Victron terminator in the other port). |
@dmsims |
| Victron |
MultiPlus-II 48/10000/140 |
CAN-bus BMS LV (500 kbit/s) |
CAN : Victron |
--- |
@cali-clim, @20after4 |
| MidNite Solar |
MN15-12KW-AIO |
PYLON |
CAN : PYLON V1 |
--- |
@goldserve, @jahyde |
| SRNE |
HESP48120U200-H |
UZE |
CAN : PYLON V2 |
Most PYLON-based protocols show same results. Inverter does not work in PYLON mode, UZE works. Incorrect temp reported. |
@ogremustcrush |
| Studer |
XTM-4000 |
Pylontech |
CAN : PYLON V2 |
DIP Switch in Xcom-CAN: 11000110 (1 to 8, ON==1). |
@kolins-cz |
| Schneider |
XW Pro 6848 NA |
Voltage Control Li-Ion |
CAN : PYLON V2 |
The extended 29-bit ACK is handled automatically since YamBMS 1.8.0, no option to set. |
@AGDorsum, @ngustas |
| SMA |
Sunny Island |
--- |
CAN : SMA |
--- |
--- |
Supported MPPT chargers
The following are confirmed and known to work:
| Brand |
Model |
Inverter bat. mode |
CAN/RS485 protocol |
Remarks |
Reported by |
| Epever |
IT-NC |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
ET-NC |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
TIS |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
TES |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
TEP |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
TBP |
BPRO 21 |
RS485 : PYLON |
--- |
--- |
| Epever |
Tracer-AN G3 |
BPRO 21 |
RS485 : PYLON |
--- |
--- |