YamBMS ( Yet another multi-BMS Merging Solution )
Caution
There is a black screen issue with
Atom S3when you compile YamBMS with ESPHome2024.8.0and above. Until this bug is fixed it is necessary to compile with ESPHome2024.7.3(this only concerns Atom S3).
Tip
If compiling the source code is too difficult for you, I can provide you a
custom firmwarethat is easy to install from a web page. You can contact me privately on the DIY solar forum.
| ESPHome application to monitor BMS and communicate with inverters supporting CAN bus protocol compatible with Pylontech, GoodWe, SMA, Victron or Luxpower (EG4). |
![]() |
|---|---|
| Note: Pylontech uses 15S/48V and many others uses 16S/51.2V ! Other battery profiles that utilise the PYLON protocol with different cell countsmay also work, e.g. Alpha Ess Smile, BYD Battery-Box LV Flex Lite. Select the correct battery profile in the inverter to match your battery pack ! The ESP32 communicates with the BMS using the BLE / UART / RS485protocol and then sends the CAN bus data to the inverter via the CAN bus transceiver. |
![]() |
Sends over CAN bus to inverter:
- Battery Voltage
- Battery Current (+charge, -discharge)
- State of Charge (SOC)
- State of health (SOH)
- BMS temperature
- Charging voltage
- Charging max amps
- Discharge min voltage
- Discharge max amps
- Battery name
- Alarms: Cell over/under voltage, Charge/discharge over current, High/low Temp, BMS fault
Note: this code support multi-BMS connection per inverter with a single ESP32 and should work with inverters that support
the CAN bus protocol PYLON, SMA, Victron or LuxPower (EG4). I'm only testing it with my Deye SUN-6K-SG03-LP1-EU inverter.
This project is still in development and testing...
Dedicated topic on DIY Solar Forum
YamBMS
Home Assistant
Contents
- Supported devices
- YamBMS behavior
- YamBMS functions
- Charging logic
- CAN bus protocol
- Schematic and setup instructions
- Configuration of the main YAML
- Installation procedure
Requirements
- ESPHome 2024.6.0 or higher
- ESP32 MCU
- CAN Transceiver (only with TJA1050/TJA1051 : 4.7K resistor for 5V to 3V3 level shifing)
- BMS JK-B*, JK-PB* (other BMS brands already integrated with ESPhome can be added easily)
- Inverters supporting CAN PYLON/Goodwe/SMA/Victron Low Voltage protocol
- Optional: 48V to 5V DC-DC converter to power the ESP32 from the JK-BMS VBAT pin (URB4805YMD-10WR3 or VRB4805S-6WR3)
- Optional: JK RS485 adaptor and RS485 to TTL 3V3 adaptor (see schematic section)
Changelog
- YamBMS 1.4.5 : Changed the way to configure WiFi/Ethernet network, added
ESP32-C3 ETH01-EVOethernet board, reduction of the number of YAML bms files, UARTrx_buffer_sizeis set to512by default for JK-B and JK-PB, new JK-BMS BLE sensors (last commits of @syssi) and new BLEstandardversion - CANBUS 2.3.6 : Sending CAN frames stops immediately if there are no combined BMS
- YamBMS 1.4.4 : Multi-shunt support, Simplified and new YamBMS option
battery chemistry, slidermin/maxvalues are automatically configured based on the battery chemistry and cell count, addedYamBMS Fallback Hotspot, added YamBMSUpdate service, added PVbrain2 and Atom Matrix board, added PSRAM settings YAML (not enabled by default), new MIN/MAX temperature sensor, added DC current icon, fixed dual sensorCell UVPR (MAX)bug, Improvedcombinecode, Breaking change : Atom S3GPIOs 1 and 2reversed - CANBUS 2.3.5 : New MIN/MAX temperature / sensor ID, Improved Victron protocol (online/offline battery modules, installed/available battery capacity)
- CANBUS 2.3.4 : Fixed bug of canbus link validation without inverter connected
- YamBMS 1.4.3 : Added Victron and Junctek KH-F
Shuntsupport andRequested Force Chargefunction based onSoC start/stop, newTotal Daily Energysensors - CANBUS 2.3.3 : Added
AutomaticBMS name selection andRequested Force ChargeBit 3/4/5 (PYLON 0x35C) - CANBUS 2.3.2 : Added
LuxPowerprotocol with updatedcan_id0x355, 0x356, 0x359 and 0x35C - CANBUS 2.3.1 : Improved the procedure for sending canbus frames with reduced loop time, rewritten of the canbus link validation code and added
Inverter Heartbeat Monitoringfunction - YamBMS 1.4.2 : Added new
Auto CVL Boost V.andRebulk SoCfunctions, new debug.yaml for ESP32 and ESP32-S3, improved code and comments - YamBMS 1.4.1 : Rewriting of the alarm system, bug fixes and improvement of the charging logic (new status
Cut-Off), icon allocation for each sensor, UART and CANBUS!extend ${vars}, New sensorYamBMS Delta Cell V., ImprovedBattery SOClogic - YamBMS 1.3.2 : New var
yambms_cell_count, the BMS charge or discharge switches can be activated separately without causing the decombination of the BMS, newminimalversion of the BMS YAML in order to reduce the loop time - YamBMS 1.3.1 : First multi-BMS version named
YamBMS
References
- Thanks to @syssi for help and making the original JK-B UART and BLE code.
- Thanks to @txubelaxu for help and making the original JK-PB RS485 code.
- Thanks to @uksa007 for making the original CANBUS code.



